pclose

    (PHP 4, PHP 5, PHP 7, PHP 8)

    pclose — Closes process file pointer

    Description

    pclose(resource $handle): int

    Closes a file pointer to a pipe opened by popen().

    Parameters

    handle

    The file pointer must be valid, and must have been returned by a successful call to popen().

    Return Values

    Returns the termination status of the process that was run. In case of an error then -1 is returned.

    Note:

    If PHP has been compiled with --enable-sigchild, the return value of this function is undefined.

    Examples

    Example #1 pclose() example

    <?php
    $handle     = popen('/bin/ls', 'r');
    pclose($handle);
    ?>

    Notes

    Note: Unix Only:

    pclose() is internally implemented using the waitpid(3) system call. To obtain the real exit status code the pcntl_wexitstatus() function should be used.

    See Also

    • popen() - Opens process file pointer

    Improve This Page

    Learn How To Improve This Page • Submit a Pull Request • Report a Bug
    ＋add a note

    User Contributed Notes 4 notes

    up
    13
    Uwe Ohse
    8 years ago
    Regarding the return value:
    "Returns the termination status of the process that was run. In case of an error then -1 is returned. "
    and the note about the exit status: "pclose() is internally implemented using the waitpid(3) system call. To obtain the real exit status code the pcntl_wexitstatus() function should be used."

    The documentation of the return value is, at best, misleading. The function returns, as does proc_close():
    * -1 on error,
    * WEXITSTATUS(status) if WIFEXITED(status) is true, or
    * status if WIFEXITED(status) is false,
    where status is the status parameter of waitpid().

    This makes it impossible to differentiate between a relatively normal exit or a termination by signal, and reduces the value of the proc_close return code to a binary one (ok / something broke).

    This can be seen in proc_open_rsrc_dtor() in ext/standard/proc_open.c (PHP 5.4.44, 5.6.12).

    The note advising the use of pcntl_wexitstatus is plain wrong. One cannot use pcntl_wexitstatus because it already has been used.
    up
    3
    kcross at nssolutions dot com
    21 years ago
    Somewhere between 4.1.1 and 4.2.3, the return value from pclose changed.

    The exit status used to be in the second byte, so that the status would be (pclose($fp)/256).

    It is now in the low-order byte, so the status is just pclose($fp).

    Be careful.
    up
    2
    vdweij at mailsurf dot com
    21 years ago
    As I understand pclose will return 0 (on every platform) in case popen could not execute the specified command.

    Since popen only returns the status wether it was able to send a command and not wether it was succesfully executed. Only the returned value of pclose can be used to check wether a command could be executed.
    up
    1
    Mike
    16 years ago
    The termination status, as pointed out in another note, is not the same as the exit status from the process. However, something like "pclose($fp)/256" is not the correct way to extract the exit status, since this uses system- and version-specific knowledge of where in the termination status the exit status is stored. (Also, the process may not even have exited normally, so it may not have an exit status at all.)

    Instead, the functions pcntl_wifexited() and pcntl_wexitstatus() should be used. They are wrappers for the C macros WIFEXITED() and WEXITSTATUS() that are designed for determining whether the process had an exit status and what that status was, respectively.
    ＋add a note
    To Top